With the cutter labels, cardboards, textiles and heat shrink tubes are cut separately, as multiple printed panels or at the end of the print job. 

 2. Perforation cutter PCU4

With the perforation cutter labels, cardboards, textiles and heat shrink tubes are perforated and cut separately, as multiple printed panels or at the end of the print job. 

Perforation cutter PCU4/2,5,  perforation distance 2.5 mm
Perforation cutter PCU4/10, perforation distance 10 mm

3. Stacker with cutter

The printed materials are cut and piled up with the stacker. The print job stops when the height of the pile is reached.
To keeo the bending of the material during piling as small as possible cab recommends a broad core diameter.
The storage table and the protective cover are adjusted to the label size and have to be ordered separatly.
With the base frame the devices can be arranged on the table in any order.

 4. Rewind guide plate for internal rewinding - for label rolls up to 145 mm Ø

The internal rewinding is operated with the dispense printer (P-version). For the printers A2+ and A4+ the peel-off plate is replaced by a rewind guide plate. 

 5. External rewinder ER1/2/3 - for direct connection onto the printer

The rewinder is bolted directly onto the printer. The label winding is optionally inside or outside. The electronic control via the swing arm provides a smooth and tight winding.

 6. External Rewinder ER 4/6/8 - with built-in power supply

The rewinder can be attached to almost every other printer. All other technical data are according  to the rewinder.

 7. External Unwinder EU 4/6/8

It enables a smooth feeding of labels for heavy rolls. The unwinder works both with inside and outside wound labels.

8. Tester for linear barcodes

The built-in scanner tests the barcode directly after printing. If the bardcode is not readable the printing process can be stopped at once so the faulty labels can be removed. It is primarily intended to be used with the external rewinder ER4 - ER8.

For 2D-Codes on request.

 9. Accessories for dispensing of labels - automaticaly or on demand

Dispensing labels requires an additional present sensor or peel-off adapter. cab offers devices both for manual operation and automatic operation.
If labels are difficult to remove from the liner a peel-off plate with rewind guide plate, extended by 10 mm, is used.

 10. Present sensor PS 8 - for manual operation

The photo cell detects the label in peeling position and pauses the labelling process. After removing the label manually the next one is printed instantly

 11. Present sensor PS 5 - for automatic operation

Printing and dispensing of labels is started with an external signal. The removal can be made by a róbot or an applicator.

Inputs: Start, label removed, external error
Outputs: No print job, printer not ready, labels in dispensing postion.

12. Present sensor PS 6 - for manual and automatic opertion

1. As with PS 8 after removing the label the next one is printed automatically.
2. Dispensing on demand with present trigger, foot switch or an external signal (according PS 5)

13. Extended present sensor PS 9 - for manual and automatic opertion

For dispensing labels where the front edge is not detected by the present sensor PS 6. The extension is made on customer-specific.

 14. Pause adapter PS 7 - for basic and dispense devices

The print job is stopped with the pause signal. The active label is finished, e.g. by using a label loop.

Inputs: Pause, external error
Outputs: No print job, printer not ready, print job active

 15. Present trigger

Starts printing and dispensing.

 16. Foot switch

Starts printing and dispensing.

 17. Sub-D plug

Connection of the external control signals for automatic operation. Sub-D plug 15-pole with screw clamps.

 18. External panel

If the panel is not accessible anymore, e.g. after installation within a facility, it is possible to install an external panel. Additionally there is a slot for a CF memory card Type 1 and a USB Master interface.